Below grade sewage ejector system manual#
Below grade sewage ejector system professional#

Now, get some bleach powder and sprinkle over the surface and leave for about 20 minutes before scrubbing. Having gotten rid of loose waste, you’ll need to scoop out white floating grease as well as gray masses. Now, put off electricity supply to the sewage ejector pump and get rid of loose waste using a water hose attached to a sprayer.

Below grade sewage ejector system manual#

The following steps should be of immense help.īefore you begin, stop the water flow in the tank, open the tank lid, and activate manual control in draining the tank. These are quite simple and easy to perform.

One of the best ways to keep your sewage ejector system serving you for long is by performing basic maintenance actions.

Below grade sewage ejector system professional#

Remember, the assistance and advice of a licensed professional will be of great benefit to you. To get the best deal available, it’s necessary to conduct a price survey as well as compare available sewage ejector system brands. Most homes will do just fine with a 30 to 40-gallon sewage holding basin. As stated earlier, there’s also the need to select an appropriate holding basin size. Sewage ejector systems are rated in horsepowers.Īlso, the size of the holding basin counts.Ī sewage ejector pump with motor power ratings of ½ to ¾ horsepower would serve the needs of most households. The size here refers to the capacity of the pump. Here, we strongly advise you to avoid taking the DIY route if you have limited plumbing experience.Īnother factor to take into consideration is the size of the sewage ejector system to purchase. In other words, the input of a professional is necessary and helps with proper installation. The entire process of installation will require the expertise of a licensed plumber. Installing A Sewage Ejector Systemīefore installing a sewage ejector system, a lot of work is required to ensure it meets set requirements.Īmong the various requirements is the need for permits, checking the building codes of the area as well as obtaining project estimates. Once the wastewater reaches this level, the sewage ejector pump is activated to start pumping. So, about 30 gallons of wastewater collects into this chamber before it’s pumped up to the main sewer line.Įfficient wastewater collection in the sump basin is aided by sloping pipes that run to the sides of the sump basin.Ī predetermined level is set with the help of a moveable float. The holding capacity for the sump basin is usually around 30 gallons. It is constructed by cutting and digging into the ground. The Sump Basinįor sewage ejector systems to function effectively there needs to be a sizeable sewage collection chamber where the ejector pump should sit. Some septic systems have drain fields that are located on a higher elevation than the septic tanks.įor the effluent to get to the drain field for further treatment, it will need to be pumped using a sewage ejector pump. One of the most common areas of application outside of the one being focused on is the septic drain field system. Other Applications of A Sewage Ejector SystemĪpart from lifting wastewater from lower plumbing systems to the main sewer or septic lines, there are other uses for sewage ejector systems. Instead of rainwater, a sewage ejector system helps in lifting or pumping up wastewater to the main sewer line for onward flow out of the home. In the case of a groundwater sump pump, rainwater seepage is being pumped out of the home. However, the only difference here is the medium being transferred. Sewage ejector systems or pump-up ejector systems as they’re sometimes called save homeowners a lot of stress.Ī sewage ejector system works similarly to a groundwater sump pump. In other words, such wastewater naturally flows to its destination which may be the septic tank or the community sewer line. Once transferred or pumped up, the action of gravity kicks in. This is the job required of a sewage ejector pump. Accumulated Wastewater Only Needs to Get to the Main Sewer LineĪs wastewater from laundry, toilets, and drains accumulate (for plumbing fixtures below the sewer or septic line), it will need to be transferred to the mainline.This helps trigger ejector pumps to get to work when the need arises. For this to happen, a timer or sensor needs to detect the level of sewage. Whenever wastewater accumulates, it gets pumped out to the main sewer line. There’s also the possibility of the main drain bursting due to pressure from accumulated sewage.Īll of these problems are resolved with the presence of a sewage ejector.